34crnimo6 specific density

1.6582 34CrNiMo6 Alloy Steel - NQA ISO certificated factory

EN 34CrNiMo6 Steel is an important alloy engineering steel grade as per BS EN 10083-3:2006. 34CrNim06 steel has high strength, high toughness and good hardenability. EN / DIN 34CrNiMo6 alloy steel has the stability of resistance to overheating, but the white sensitivity of 34CrNiM06 is high. 2541 (SS ) - Worldwide equivalent grades34CrNiMo6 (1.6582) , 2541 (Sweden, SS ) - European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt

34CrNiMo6 - Grade,Structural Steel - Specific Steel

e.g.17-4PH, PH13-8Mo, 422 Phone:(+86) 8 0247 006 Email:[email protected] Contact 34CrNiMo6 - Special Alloy - Specific Steel34CrNiMo6 Special Alloy Chemical composition%of the ladle analysis of grade34CrNiMo6. C() Si() Mn() 4340 AISI 4340 SAE 4340 Alloy Steel - SAE AISI 1010 1015 4340 - Highly alloyed steel, nominally 1.8% Ni, .80% chromium and .25% molybdenum. High strength characteristics. Used for heavily stressed parts operating in fatigue and other duty conditions. AISI 4340 has a favorable response to heat treatment usually oil quenching followed by tempering and exhibits a good combination of ductility and strength when treated thusly.

4340 Steel 36CrNiMo4 1.6511 EN24 SNCM439 - Otai

AISI 4340 steel is a medium carbon, low alloy steel. Otai steel is one leading supplier of 4340 steel & equivalents:36CrNiMo4, 1.6511, EN24, SNCM439 etc. DIN 1.6582 34CrNiMo6 - Waldun SteelDIN 1.6582/34CrNiMo6 steel is used to make tools which requires good plasticity and high strength. It is usually selected to make the big size and important parts, such as heavy machinery axle,turbine shaft blade, high load of transmission parts, fasteners, crank shafts, gears, as well as heavily loaded parts for motor construction etc. Difference Between Density and Specific GravitySep 03, 2019 · However, because the density of pure water is so close to 1 (0.9976 grams per cubic centimeter), specific gravity and density are nearly the same value so long as the density is given in g/cc. Density is very slightly less than specific gravity.

EN 1.6582 (34CrNiMo6) Steel ::MakeItFrom

May 30, 2020 · EN 1.6582 (34CrNiMo6) Steel. EN 1.6582 steel is an alloy steel formulated for primary forming into wrought products. 1.6582 is the EN numeric designation for this material. 34CrNiMo6 is the EN chemical designation. It has a moderately high electrical conductivity among EN wrought alloy steels. In addition, it has a moderately low thermal conductivity and a fairly high base cost. EN10083 1.6582 34CrNiMo6 Hardening Steel ssroundbarWe are responsive company based on principle of uncompromising commitment to excellence in our EN10083 1.6582 34CrNiMo6 Hardening Steel products and services. We have good source for stockists and manufacturer EN10083 1.6582 34CrNiMo6 Hardening Steel.We extend a qualitative range of EN10083 1.6582 34CrNiMo6 Hardening Steel to our clients that is manufacturer in compliance with Steel Grade Equivalents Guide Hillfoot34CrNiMo6 (C36) 40CrNiMo6:1.6565 1.6582:4340 (43B) 4145 (41I) 4340 (43B) 826M40 (826) 4330V (43V) 826M40 (826) EN26 :40NiMoCr10-5:1.6745 :4340 (43B) 4330V (43V) 835M30 (83A) EN30B :30NiCrMo16-6:1.6747 :1.2767:4330V (43V) 722M24 (722) EN40B :32CrMo12:1.7361 :535A99 (535) EN31 :100Cr6 (CC1) 1.3505:52100 :100CrMo7-3 (CC3) Stocked

TECHNICAL DATA SHEET 34CrNiMo6 1 - dew-stahl

34CrNiMo6 1.6582 F 8 Firmodur 6582 is used for through-hardened components such as fasteners in the automotive and mechanical engineering industry with high demands on strength and toughness. APPLICATIONS DELIVERY CONDITION Quenched and tempered 700 1,400 MPa Soft annealed (+A) max. 248 HB QUENCHED AND TEMPERED STEEL