chemical compostion of raw material fe 310 st 32 as per is

(II-1-2) Steel and Iron Materials - DNV

8.1 Testing of chemical composition The manufacturer shall determine the chemical com-position of each melt and shall submit a corresponding certificate to the Surveyor. The chemical composition specified for the steel grade shall be shown in the certificate. Chapter 2 Page 12 Section 1 Steel Plates, Strips, Sections and Bars II - Part 1 GL IS 2062 (2011):Hot Rolled Medium and High Tensile cooling conditions as per the agreement between the purchaser and the manufacturer/supplier. 6.3 Material produced by re-rolling finished products (virgin or used or scrap), or by rolling material for which the metallurgical history is not fully documented or not known, are not acceptable as per this standard. 7 FREEDOM FROM DEFECTS

London Metal Exchange:Ferrous

The LME offers two ferrous contracts, LME Steel Rebar and LME Steel Scrap; cash-settled futures which are designed to meet the needs of the metal community for new risk management tools. MATERIAL GRADES - MeusburgerRAW MATERIALS. 3 0 24 20 100 200 300 400 500 600 700 The Meusburger Here the plates are cooled by approximately 35°C per hour. If they were cooled more quickly, tension - and even the formation of cracks - could once more occur in the material. S 355 J2 (St 52-3) A 52 FP A738 C Si Mn Mencinger's Webfe 310-0. st 33. a 33. a 310-0. fe 320. a 320. 13 00-00. fe 310-0. st 320. s235jr. 1.0037. fe 360 b. st 37-2. e 24-2. fe 360 b. ae 235-b. 13 11-00. fe 360-b. ns 12 120. s235jrg1. 1.0036. fe 360 bfu. ust 37-2 - - - ae 235 b-fu. ust 360 b. ns 12 122. s235jrg2. 1.0038. fe 360 bfn. rst 37-2 - - - 40 b. ae 235 b-fn

SG Iron Casting Grades and Standards

The followings are the grade requirement to the chemical components and physical properties, and also grade comparison chart. At the same time, we listed the main content of material standards using in USA, China, Germany, Europe and International. Please notice that the chemical components are only a reference, not a strict standard to the Stainless Steel - Grade 304Grade 304 is the standard "18/8" stainless; it is the most versatile and most widely used stainless steel, available in a wider range of products, forms and finishes than any other. Stainless Steel - Grade 316L (UNS S31603) - Material Science

  • Key PropertiesGrade Specification ComparisonCorrosion ResistanceHeat ResistanceHeat TreatmentWeldingMachiningHot and Cold WorkingHardening and Work HardeningApplicationsThese properties are specified for the flat-rolled products (plate, sheet, and coil) in ASTM A240/A240M. Similar but not necessarily identical properties are specified for other products such as pipe and bar in their respective specifications.TABLE - 1 - HindalcoTABLE-3 Wrought alloys :Chemical composition limits (per cent) 12 Introduction 1 C 19000 1100 - 0.10 - - - 0.5 0.6 - 0.1 0.1 Aluminium 99.0% Min 1200 - 0.05 - - Si+Fe 1.0 - 0.05 0.1 Aluminium 99.0% Min

    Stainless Steel - Material Science News Materials

    • Chemical FormulaKey PropertiesMechanical PropertiesGrade Specification ComparisonCorrosion ResistanceHeat ResistanceHeat TreatmentWeldingMachiningDual CertificationFe, <0.03% C, 16-18.5% Cr, 10-14% Ni, 2-3% Mo, <2% Mn, <1% Si, <0.045% P, <0.03% S Grade 316 is the standard molybdenum-bearing grade, second in importance to 304 amongst the austenitic stainless steels. The molybdenum gives 316 better overall corrosion resistant properties than Grade 304, particularly higher resistance to pitting and crevice corrosion in chloride environments. It has excellent forming and welding characteristics. It is readily brake or roll formed into a variety of parts for applicatioEquivalents of Carbon Steel QualitiesMesteel Is A B2b Portal. It Provides Steel And Construction Related Companies In The Middle East Information, News And An Extensive Interactive Database, Inclusive Offers And Inquiries.Chemical composition of stainless steelClassification Specification Chemical Composition other; JIS AISI C Si Mn P S Ni Cr Mo Cu N; Martensitic Grades:SUS403:403:Max.0.15:Max.0.50:Max.1.00:Max.0.040