aisi 4130 tensile strength

4130 Steel AISI 4130 1.7218 25CrMo4 SCM430

WALDUN is supplying with round,square,flat,block,and shaft etc. AISI 4130 steel is defined as a low alloy steel which contains 1%Cr and 0.2%Mo as strengthening alloy offers good strength,toughness, corrosion resistance and machinability.Compared with AISI 4140 steel,It has lower carbon,0.28-0.33%so it can be welded easily. AISI 4130 steel is commonly supplied in the 4130 vs 4140 Steel Comparison Capital Steel & WireThe following is a comparison of 4130 grade steel and 4140 grade steel. This information may be useful for machining purposes and as a resource for purchasing 4130 and 4140 steel. Chemical Properties. The chemical properties of 4130 and 4140 steel are similar aside from differences in

AISI 4130 Alloy Steel - West Yorkshire Steel

AISI 4130 is a chromium molybdenum alloy steel specification. It is supplied as round bar commonly in the hardened and tempered condition with a hardness of 18-22 HRc. With a lower carbon content range AISI 4130 provides better weldability, at the expense of through thickness strength, than that of other oil and gas steel grades such as AISI 4140. AISI 4130 Flanges:Alloy Steel SAE 4130 Chromoly Blind Being a versatile alloy grade, the 4130 Aircraft Steel SORF Flanges tend to exhibit good resistance to atmospheric corrosion and while offering reasonable tensile strength. Overall the attractive combination of properties such as strength, toughness in addition to fatigue strength is why these API 60k Alloy Steel AISI 4130 Flanges are used in several applications. AISI 4130 Steel, annealed at 865°C (1590°F)AISI 4130 Steel, annealed at 865°C (1590°F) Tensile Strength, Ultimate; Tensile Strength, Yield; Elongation at Break, in 50 mm; Reduction of Area; Modulus of Elasticity, Typical for steel; Bulk Modulus, Typical for steel; Poissons Ratio, Calculated; Machinability, annealed and cold drawn. Based on 100% machinability for AISI 1212 steel.

Encore Metals - 4130

Hardened & Tempered:840/ 870 Water quench, 855/ 885 Oil quench; 430/ 700 According to properties required. Mechanical Properties. Annealed Typical. Tensile Strength - 80,000 psi. Yield Strength - 80,000 psi. Elongation - 28%. Reduction of Area - 57%. Hardness - SAE-AISI 4130 (SCM430, G41300) Cr-Mo Steel ::May 30, 2020 · SAE-AISI 4130 steel is an alloy steel formulated for primary forming into wrought products. 4130 is the designation in both the SAE and AISI systems for this material. G41300 is the UNS number. The properties of SAE-AISI 4130 steel include four common variations. This page shows summary ranges across all of them. eFunda:Properties of Alloy Steel Alloy Steel AISI 4130Tensile Properties :T (°C) Treatment:25:annealed at 865°C :Tensile Strength (MPa) 560.5 :Yield Strength (MPa) 360.6 :Elongation (%) 28.2 :Reduction in Area (%) 55.6 :25:normalized at 870°C :Tensile Strength (MPa) 668.8 :Yield Strength (MPa) 436.4 :Elongation (%) 25.5 :Reduction in Area (%) 59.5 :25:water quenched, fine grained

eFunda:Properties of Alloy Steel AISI 4130

Tensile Strength (Mpa) 560.5 :25 :annealed at 865°C more:Yield Strength (Mpa) 360.6 :Elongation (%) 28.2 :Reduction in Area (%) 55.6 :Hardness (HB) 156 :25 :annealed at 865°C more:Impact Strength (J) (Izod) 61.7 :25 :annealed at 865°C more